Componenten Anschluss tuts nicht

  • Hey Liebe Raspberry Gemeinde bin noch ganz neu hier im Forum und bin mit nit 100 pro sicher das ich jetzt in der richtigen Kategorie bin aber naja.
    Also ich wollte heute den Komponenten Ausgang ausprobieren, da ich mir einen kleinen Rückfahrmonitor kaufen möchte. Jetzt habe ich den Pi mal an unseren Samsung Plasma Tv angeschlossen und auch auf pal umgestellt das gleiche habe ich auch an einer alten Röhre ausprobiert. Doch es gab kein Bild habe hdmi force hotplug aus also daran liegts nit. Bitte um Antworten.
    Lg Mrpi23

  • Danke für denn Tipp aber irgendwie fehlt die Option hier :

    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1

    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1

    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16

    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720

    # uncomment if hdmi display is not detected and composite is being output
    hdmi_force_hotplug=1

    # uncomment to force a specific HDMI mode (this will force VGA)
    #hdmi_group=1
    #hdmi_mode=1

    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2

    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4

    # uncomment for composite PAL
    #sdtv_mode=2

    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800

    # for more options see http://elinux.org/RPi_config.txt
    gpu_mem=128


    was jetzt?

  • Ich habs ausprobiert funkt aber immer noch nit ! :

    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1

    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1

    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16

    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720

    # uncomment if hdmi display is not detected and composite is being output
    hdmi_force_hotplug=1

    # uncomment to force a specific HDMI mode (this will force VGA)
    #hdmi_group=1
    #hdmi_mode=1

    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2

    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4

    # uncomment for composite PAL
    #sdtv_mode=2

    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800

    # for more options see http://elinux.org/RPi_config.txt
    gpu_mem=128

    # composite on
    hdmi_ignore_hotplug=1

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!