Hi Leute!
Wirklich ein super Forum hier. Habe mir schon viele Anregungen bezüglich der Einstellungen meines Insanelights geholt. Leider habe ich jedoch noch ein Problem, was mich etwas stört.
Problematik:
Die Übergänge zwischen den Farben und bei Auf- und Abblendungen sind mir eindeutig noch zu zackig. Jemand hier im Forum hatte es mal ganz passend mit Prozentzahlen beschrieben. Es gibt quasi Sprünge von 100% Leuchtkraft auf 90%, 80% etc. und nicht etwa kleine Abstufungen von 100% auf 99%, 98% etc. Ich habe jetzt schon alles mögliche in den Einstellungen von Hyperion ausprobiert, aber irgendwie will das nicht so richtig helfen. Auch die diversen anderen Threads zu ähnlichen Themen haben mich hier nicht weiter gebracht. Daher habe ich auch den neuen hier aufgemacht. Vllt. liegt es ja an meinem ganz spezifischen Aufbau...
Aufbau:
- Mein Fernseher ist ein 55" TV von Samsung (UE55H6470).
- TV ist per Wandhalterung angebracht (Abstand der LED-Stripes zur Wand zwischen 5 u. 7cm).
- Abstrahlwinkel der LED sind geschätzte 15-20°, da die Rückwand des TV nicht ganz gerade ist.
- Die Wand dahinter besteht aus weißen Holzpaneelen. Diese sind ganz leicht spiegelnd. Aber wirklich nur ganz leicht.
- Ich benutze ein vorkonfiguriertes Insanelight (siehe hier).
- Es sind insgesamt 180 LEDs.
- Das ganze wird gesteuert von einem Raspberry PI B.
Also wie gesagt, ich bin wirklich sehr zufrieden mit dem Set und auch meine Farben habe ich für mich schon perfekt eingestellt. Einzig und allein die Übergänge wirken mir noch zu ruckartig bzw. nicht fein genug.
Ich weiß leider nicht, woran es liegt. Liegt es evtl. daran, dass der Fernseher so nah an der Wand ist und die Rückwand ganz leicht spiegelt, wodurch sich die einzelnen LEDs zu stark abzeichnen und die Lichtkegel nicht gut genug miteinander vermischen? Habe diesbezüglich leider keine Erfahrungen und die Möglichkeit, das ganze weiter abzuziehen besteht leider nicht. Die Wandhalterung ist fix und das Rack voll belegt.
Oder aber liegt es vielleicht daran, dass das Signal nicht schnell genug nach Einblendung des Bildes verarbeitet wird bzw. ans Ambilight weitergegeben wird?
Ich wollte auch ein Video machen, jedoch wirkt es auf dem Video so, als sei es bereits sehr flüssig und homogen. Daher bringt das eher nichts.
Schon einmal vielen Dank im Voraus für eure Hilfe. Bin für jede Anregung dankbar!
Hier noch meine gekürzte Config-Datei:
ZitatAlles anzeigen
//ambi55-3 120x70 34-56
// Automatically generated configuration file for 'Hyperion daemon'
// Generated by: HyperCon (The Hyperion deamon configuration file builder{
/// Device configuration contains the following fields:
/// * 'name' : The user friendly name of the device (only used for display purposes)
/// * 'type' : The type of the device or leds (known types for now are 'ws2801', 'ldp8806',
/// 'lpd6803', 'sedu', 'adalight', 'lightpack', 'test' and 'none')
/// * 'output' : The output specification depends on selected device. This can for example be the
/// device specifier, device serial number, or the output file name
/// * 'rate' : The baudrate of the output to the device
/// * 'colorOrder' : The order of the color bytes ('rgb', 'rbg', 'bgr', etc.).
"device" :
{
"name" : "MyPi",
"type" : "lpd8806",
"output" : "/dev/spidev0.0",
"rate" : 500000,
"colorOrder" : "brg"
},/// Color manipulation configuration used to tune the output colors to specific surroundings.
/// The configuration contains a list of color-transforms. Each transform contains the
/// following fields:
/// * 'id' : The unique identifier of the color transformation (eg 'device_1') /// * 'leds' : The indices (or index ranges) of the leds to which this color transform applies
/// (eg '0-5, 9, 11, 12-17'). The indices are zero based. /// * 'hsv' : The manipulation in the Hue-Saturation-Value color domain with the following
/// tuning parameters:
/// - 'saturationGain' The gain adjustement of the saturation
/// - 'valueGain' The gain adjustement of the value
/// * 'red'/'green'/'blue' : The manipulation in the Red-Green-Blue color domain with the
/// following tuning parameters for each channel:
/// - 'threshold' The minimum required input value for the channel to be on
/// (else zero)
/// - 'gamma' The gamma-curve correction factor
/// - 'blacklevel' The lowest possible value (when the channel is black)
/// - 'whitelevel' The highest possible value (when the channel is white)
///
/// Next to the list with color transforms there is also a smoothing option.
/// * 'smoothing' : Smoothing of the colors in the time-domain with the following tuning
/// parameters:
/// - 'type' The type of smoothing algorithm ('linear' or 'none')
/// - 'time_ms' The time constant for smoothing algorithm in milliseconds
/// - 'updateFrequency' The update frequency of the leds in Hz
"color" :
{
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsv" :
{
"saturationGain" : 1.0000,
"valueGain" : 1.1000
},
"red" :
{
"threshold" : 0.1000,
"gamma" : 2.2300,
"blacklevel" : 0.0000,
"whitelevel" : 0.8500
},
"green" :
{
"threshold" : 0.1000,
"gamma" : 2.1000,
"blacklevel" : 0.0000,
"whitelevel" : 0.7000
},
"blue" :
{
"threshold" : 0.1000,
"gamma" : 2.2200,
"blacklevel" : 0.0000,
"whitelevel" : 0.6500
}
}
],
"smoothing" :
{
"type" : "linear",
"time_ms" : 100,
"updateFrequency" : 50.0000
}
},/// The configuration for each individual led. This contains the specification of the area
/// averaged of an input image for each led to determine its color. Each item in the list
/// contains the following fields:
/// * index: The index of the led. This determines its location in the string of leds; zero
/// being the first led.
/// * hscan: The fractional part of the image along the horizontal used for the averaging
/// (minimum and maximum inclusive)
/// * vscan: The fractional part of the image along the vertical used for the averaging
/// (minimum and maximum inclusive)LEDs in der Config hier wegen der Übersichtlichkeit entfernt!
/// The black border configuration, contains the following items:
/// * enable : true if the detector should be activated
/// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.1
},/// The configuration of the effect engine, contains the following items:
/// * paths : An array with absolute location(s) of directories with effects
/// * bootsequence : The effect selected as 'boot sequence'
"effects" :
{
"paths" :
[
"/opt/hyperion/effects"
]
},"bootsequence" :
{
"effect" : "Rainbow swirl fast",
"duration_ms" : 5000
},/// The configuration for the frame-grabber, contains the following items:
/// * width : The width of the grabbed frames [pixels]
/// * height : The height of the grabbed frames [pixels]
/// * frequency_Hz : The frequency of the frame grab [Hz]
// "framegrabber" :
// {
// "width" : 117,
// "height" : 67,
// "frequency_Hz" : 25.0
// },/// The configuration of the XBMC connection used to enable and disable the frame-grabber. Contains the following fields:
/// * xbmcAddress : The IP address of the XBMC-host
/// * xbmcTcpPort : The TCP-port of the XBMC-server
/// * grabVideo : Flag indicating that the frame-grabber is on(true) during video playback
/// * grabPictures : Flag indicating that the frame-grabber is on(true) during picture show
/// * grabAudio : Flag indicating that the frame-grabber is on(true) during audio playback
/// * grabMenu : Flag indicating that the frame-grabber is on(true) in the XBMC menu
/// * grabScreensaver : Flag indicating that the frame-grabber is on(true) when XBMC is on screensaver
/// * enable3DDetection : Flag indicating that the frame-grabber should switch to a 3D compatible modus if a 3D video is playing
// "xbmcVideoChecker" :
// {
// "xbmcAddress" : "127.0.0.1",
// "xbmcTcpPort" : 9090,
// "grabVideo" : true,
// "grabPictures" : true,
// "grabAudio" : true,
// "grabMenu" : false,
// "grabScreensaver" : true,
// "enable3DDetection" : true
// },/// The configuration of the Json server which enables the json remote interface
/// * port : Port at which the json server is started
"jsonServer" :
{
"port" : 19444
},/// The configuration of the Proto server which enables the protobuffer remote interface
/// * port : Port at which the protobuffer server is started
"protoServer" :
{
"port" : 19445
},/// The configuration of the boblight server which enables the boblight remote interface
/// * port : Port at which the boblight server is started
// "boblightServer" :
// {
// "port" : 19333
// },
/// Configuration for the embedded V4L2 grabber
/// * device : V4L2 Device to use [default="/dev/video0"]
/// * input : V4L2 input to use [default=0]
/// * standard : Video standard (no-change/PAL/NTSC) [default="no-change"]
/// * width : V4L2 width to set [default=-1]
/// * height : V4L2 height to set [default=-1]
/// * frameDecimation : Frame decimation factor [default=2]
/// * sizeDecimation : Size decimation factor [default=8]
/// * priority : Hyperion priority channel [default=800]
/// * mode : 3D mode to use 2D/3DSBS/3DTAB (note: no autodetection) [default="2D"]
/// * cropLeft : Cropping from the left [default=0]
/// * cropRight : Cropping from the right [default=0]
/// * cropTop : Cropping from the top [default=0]
/// * cropBottom : Cropping from the bottom [default=0]
/// * redSignalThreshold : Signal threshold for the red channel between 0.0 and 1.0 [default=0.0]
/// * greenSignalThreshold : Signal threshold for the green channel between 0.0 and 1.0 [default=0.0]
/// * blueSignalThreshold : Signal threshold for the blue channel between 0.0 and 1.0 [default=0.0]
"grabber-v4l2" :
{
"device" : "/dev/video0",
"input" : 0,
"standard" : "no-change",
"width" : 720,
"height" : 576,
"frameDecimation" : 1,
"sizeDecimation" : 8,
"priority" : 1100,
"mode" : "2D",
"cropLeft" : 16,
"cropRight" : 18,
"cropTop" : 04,
"cropBottom" : 14,
"redSignalThreshold" : 0.065,
"greenSignalThreshold" : 0.065,
"blueSignalThreshold" : 0.065
},
"endOfJson" : "endOfJson"
}