Kamera wird nicht erkannt. Defekt?

  • Hallo Forenmitglieder,

    ich habe mir das Raspberry Pi Kamera Modul Rev. 1.3 bestellt.
    In meiner Vorfreude steckte ich es sofort in den nächstbesten Slot. Den Display Slot!
    Die LED leuchtete und ich machte mich sofort daran das Modul in der raspi-config zu aktivieren und raspistill auszuführen.
    Zu meiner Verwunderung kam, dass keine Kamera erkannt wurde. Schnell stellte ich das Problem fest und steckte sie in den richtigen Slot.
    Dort leuchtet die LED NICHT! Kamera Support ist aktiviert, aber die Kamera selber wird nichtmal erkannt. (Bei raspistill kommt die Fehlermeldung Camera not detected.)
    Ist es möglich, dass ich sie dadurch kaputt gemacht habe?
    Wenn ich sie in den Display Port stecke leuchtet die LED.
    Ist möglicherweise mein Kamera-Modul-Port am Raspberry Pi defekt?
    Richtig eingesteckt ist sie: Blauer Streifen zum Ethernet-Port. Kontakte zum HDMI-Port.
    Bitte um Hilfe!
    Danke schonmal im Voraus!

    Viele Grüße
    Lukas

  • Wie hattest du denn die PiCam am DSI Port angeschlossen? Mit den Kontakten des Flachbandkabels zum HDMI Port? Dann kann es gut sein, dass du das PiCam Board getötet hast, denn der DSI Port ist anders belegt als der CSI Port für die PiCam. Allerdings - die LED auf dem PiCam Board leuchtet normalerweise nur dann, wenn du gerade ein Bild machst oder ein Video aufnimmst. Das die LED nicht leuchtet wenn du die PiCam am CSI Port angeschlossen hast bedeutet erstmal nicht, dass die PiCam schon von dir gegangen ist. Du hast den Pi (mit angeschlossener PiCam) schonmal komplett neu gestartet und die PiCam in der raspi-config nochmal neu aktiviert?

  • Hatte sie leider richtigherum im Display-Port. Kontakte zum HDMI-Port... :(
    Ja habe eigentlich schon alles mögliche probiert. Neu aktiviert, neugestartet. Kamera angeschlossen.
    Habe sogar schon raspbian komplett neu installiert...
    Kann man irgendwie testen, ob er überhaupt irgendetwas am CSI Port erkennt?

  • Dann kannst du nur nochmal das Flachbandkabel, dessen Kontakte an beiden Enden und die Connectoren auf den Boards auf Beschädigungen oder fehlerhafte Lötstellen überprüfen. Hast du noch nen anderen Pi oder eine andere PiCam zum gegentesten?

    Automatisch zusammengefügt:

    Es ging wohl schon einigen wie dir. Es sieht danach aus, als ob du das Camera Board in die ewigen Jagdgründe geschickt hast oder es einen Defekt hat:

    Zitat

    If you get this message you have a hardware issue - either a dodgy connection, or a failed unit. I'm not sure how you expect anyone to resolve this magically for you via software.

    Check:

    • the SUNNY connector - they are known to partially disconnect.
    • Check both ends of the flexi. Disconnect and reconnect them both. Check for any sharp bends in it as they can crack the tracks. Replace if necessary.
    • Check your power supply is up to the job. Powering up the camera takes about 300mA IIRC, and can cause the power supply lines to drop too low to actually function.
    • If possible check against another Pi and/or another Pi camera to identify which is causing issue.
      There has been at least one confirmed case of the CSI-2 connector on the main Pi having duff solder joints.
      The sensor modules are static sensitive and originally were intended to be embedded permanently in a mobile phone rather than exposed on a board. Most of the logic lines have some buffering on the small PCB so are likely to survive static shocks, but the CSI-2 lines go direct to the sensor so are going to be more sensitive.

    If the camera fails to start up at all, then the sensor isn't detected on the I2C bus. If you get this error of no data received, then the CSI-2 lanes are at fault.

    Yes, the message changed back in March because I got fed up with people reporting MMAL error 0x4f525245 having failed to search on the forums. It now tells you pretty much what the error is, but people still come here to ask - grrr!

    I've had one (abused) sensor fail on me in the last few days with these errors. As I happen to have spares of most bits kicking around I did some swapping, and in my case it is the OV5647 module itself that has failed. It has been swapped between boards many times and floating around in a rucksack (generally in an antistatic bag) for the past few months, so it really is abuse.

    Hier ist der Original Thread aus dem ich zitiere und in diesem Thread gibt es ein paar Bilder von einem CSI Hardware Defekt.

    Ein amtliches Netzteil hast du hoffentlich am Start - um diesen immer wieder auftretenden Fehler ausschließen zu können.

    Einmal editiert, zuletzt von doing (27. September 2015 um 12:02)

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!