Hallo Jungs,
ich hoffe ihr könnt mir einwenig helfen.
habe eine LANCOM USB-300agn WLAN Karte.
Die Karte funktioniert nach anfängliche schwierigkeiten, jedoch ohne N-Standard.
Hier mal ein paar outputs
Code
root@UltraSlim:~# lsusb
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 0cf3:9170 Atheros Communications, Inc. AR9170 802.11n
Code
root@UltraSlim:~# iwconfig
wlan0 IEEE 802.11abgn ESSID:"M.........N"
Mode:Managed Frequency:2.462 GHz Access Point: 00:1F:3F:19:B4:8C
Bit Rate=52 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-37 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:11 Invalid misc:168406 Missed beacon:0
Code
root@UltraSlim:~# iw list
Wiphy phy0
Band 1:
Capabilities: 0x184e
HT20/HT40
SM Power Save disabled
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15, 32
Frequencies:
* 2412 MHz [1] (20.0 dBm)
......
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
........
* 54.0 Mbps
Band 2:
Capabilities: 0x184e
HT20/HT40
SM Power Save disabled
RX HT40 SGI
No RX STBC
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15, 32
Frequencies:
* 4920 MHz [-16] (disabled)
* 4940 MHz [-12] (disabled)
......
* 5230 MHz [46] (20.0 dBm) (passive scanning, no IBSS)
Bitrates (non-HT):
* 6.0 Mbps
........
* 54.0 Mbps
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* CMAC (00-0f-ac:6)
Alles anzeigen
Wie man an den Bit-Rates sieht wird kein einziger N-Standard untertützt.
hab ihr eine Idee wie ich es hinbekomme das der N-Standard unterstützt wird?
Danke für eure Hilfe.
Gruß
Matze