Lightberry - HDMI Premium kit - bekomme es nicht hin

L I V E Stammtisch ab 20:30 Uhr im Chat
  • Hallo zusammen...

    Ich habe auf meinem Raspberry das Raspbian image von der Lightberry homepage installiert...

    Mit der Hyperion app kann ich auch die Farben der Leds ändern... und effekte gehen auch..

    Doch irgendwie geht das beim TV gucken nicht... Leds leuchten alle in einer Farbe..

    Hier mal ein auszug aus lsusb und ls /dev

    pi@raspberrypi ~ $ lsusb
    Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
    Bus 001 Device 004: ID 05e1:0408 Syntek Semiconductor Co., Ltd STK1160 Video Cap ture Device
    pi@raspberrypi ~ $


    pi@raspberrypi ~ $ ls /dev
    autofs loop2 ptmx random tty14 tty30 tty47 tty63 vcsa
    block loop3 pts raw tty15 tty31 tty48 tty7 vcsa1
    btrfs-control loop4 ram0 root tty16 tty32 tty49 tty8 vcsa2
    bus loop5 ram1 shm tty17 tty33 tty5 tty9 vcsa3
    cachefiles loop6 ram10 snd tty18 tty34 tty50 ttyAMA0 vcsa4
    char loop7 ram11 sndstat tty19 tty35 tty51 ttyprintk vcsa5
    console loop-control ram12 spidev0.0 tty2 tty36 tty52 uinput vcsa6
    cpu_dma_latency MAKEDEV ram13 spidev0.1 tty20 tty37 tty53 urandom video0
    disk mapper ram14 stderr tty21 tty38 tty54 vc-cma xconsole
    fb0 mem ram15 stdin tty22 tty39 tty55 vchiq zero
    fd mmcblk0 ram2 stdout tty23 tty4 tty56 vc-mem
    full mmcblk0p1 ram3 tty tty24 tty40 tty57 vcs
    fuse mmcblk0p2 ram4 tty0 tty25 tty41 tty58 vcs1
    input net ram5 tty1 tty26 tty42 tty59 vcs2
    kmsg network_latency ram6 tty10 tty27 tty43 tty6 vcs3
    log network_throughput ram7 tty11 tty28 tty44 tty60 vcs4
    loop0 null ram8 tty12 tty29 tty45 tty61 vcs5
    loop1 ppp ram9 tty13 tty3 tty46 tty62 vcs6


    Ich hoffe das bringt euch etwas...

    Bei schwarz gehen die Leds leider auch nicht aus
    Hier noch die config
    http://workupload.com/file/fbiUmDAQ

    Einmal editiert, zuletzt von Schmello (6. Januar 2015 um 13:46)

  • Lightberry - HDMI Premium kit - bekomme es nicht hin? Schau mal ob du hier fündig wirst!

  • das Image von Lightberry funktioniert aber, ich nutze das auch.
    in deiner config fehlt der grabber part:

    beispiel:

    Einmal editiert, zuletzt von luigii85 (6. Januar 2015 um 15:51)

  • Ich habe die config mit dem hyperion tool erstellt... muss ich das was du gepostet hast einfach in meine config rein kopieren?

    Ich habe das Gefühl das die Leds ein wenig die farbe wechseln.. aber nie ganz ausgehen...

    Hast du zufällig auch das premium hdmi kit? dieses all in one gerät von lightberry..
    Bei dem Gerät habe ich mit meiner gigablue quad einen grünstich im bild.. mit dem FireTV nicht... irgendwie will heute gar nix klappen...

    ein graus ist/war natürlich auch... als ich zuerst sauber die Klettstreifen an den TV angebracht habe... danach die Leds befästigt.. und nach LED ich weiß nicht 30.. habe ich dann gesehen das von den 4 Leitungen 2 einen defekt haben und durchgeschnitten sind... :wallbash:

    Hab den Lightberry jungs schon geschrieben... noch keine Antwort..

  • so das habe ich gemacht :)

    Habe sie mit meienr config verglichen.. ich habe nur meine Led reihenfolge in die config von Lightberry kopiert...

    Dann ein Test video durchlaufen lassen.. farben passen.. bis zu dem punkt wo vom lightberry die Kabel defekt sind... ^^

    Dann mal den Pacific rim Trailer angemacht... leider ist bei schwarz die Leds immer noch an...

    Hier meine aktuelle cfg
    http://workupload.com/file/LhiHpVhu

  • Hallo und ein gesundes neues Jahr,
    zu den durchtrennten Kabeln kann ich sagen das es bei mir auch so ist. Es sind sicher die stromführenden die in der mitte unterbrochen sind,bei mir sieht mann das sie ordentlich versiegelt sind.Zu deinem Schwarzproblem, nimm doch mal die threshold werte hoch,bei mir 0,06 hat es funktioniert.

  • 1. Wenn der Teil grabber-v4l2 richtig funktionieren soll, musst Du als Erstes mal weiter oben in Deiner Config diesen Teil hier auskommentieren..

    "framegrabber" :
    {
    "width" : 64,
    "height" : 64,
    "frequency_Hz" : 10.0
    },

    2. Warum ist beim grabber-v4l2 die Zeile "standard" : "PAL", auskommentiert?

    Ich weis nicht warum Lightberry das so in Ihre Config rein schreibt.

    So wie ich gelesen habe ist doch dort ein STK 1160 Grabber verbaut.

    3. Die crop-Werte von 1, bei grabber-v4l2 sind auch unrealistich, oder?
    Ich würde die grundsätzlich alle auf mindestens 5 setzen.
    Oder selbst per Scrennshot-Befehl anpassen.

    Vielleicht irre ich mich auch und bei Lightberry ist alles anders.

  • Der erste part steht doch so in der cfg

    /// The configuration for the frame-grabber, contains the following items:
    /// * width : The width of the grabbed frames [pixels]
    /// * height : The height of the grabbed frames [pixels]
    /// * frequency_Hz : The frequency of the frame grab [Hz]
    "framegrabber" :
    {
    "width" : 64,
    "height" : 64,
    "frequency_Hz" : 10.0
    },

    so ist er doch nicht ausgeklammert oder?

    Ich hätte nicht gedacht das es so eine umstellum vom Arduino mit Boblight auf einem Linix Receiver zu Hyperion ist ^^

    Ich habe damit die Leds bei schwarzem bild ausgehen den Threshold von 0.0 auf 0.1 gesetzt wie habt ihr das?

    Und der obere Teil und untere Teil laufen noch nicht.. blackbar läuft irgendwie nicht...
    /// The black border configuration, contains the following items:
    /// * enable : true if the detector should be activated
    /// * threshold : Value below which a pixel is regarded as black (value between 0.0 and 1.0)
    "blackborderdetector" :
    {
    "enable" : true,
    "threshold" : 0.01
    },

  • soo wenn ich diesen teil ausklammer
    "framegrabber" :
    {
    "width" : 64,
    "height" : 64,
    "frequency_Hz" : 10.0
    },

    dann laufen die leds leider nicht...
    hab es wieder zurück gestellt...

    Ja jetzt wäre nur noch die schwarze balken erkennung die nicht geht..
    Hat da jemand noch eine idee?

  • Lightberry wird ja nicht anders sein wie der rest... ist eben nur ein fertiges plug and play system ^^

    mir gefällt deren klett system echt gut :)

    hmm bei 0.02 will er die Balken noch nicht erkennen...

    Aber mal was anderes.. schaltet ihr euren Pi einfach vom strom weg? :)

  • Black Border ist bei mir auf 0.1. Pi ist immer am Strom.

    Du musst den framegrabber Part auskommentieren, und dafür den grabber-v4l2 in die config rein kopieren und villeicht noch die Parameter für dich anpassen.

    Du kannst aber auch den grabber Teil komplett weg lassen und manuell über ssh starten. Ich mache das z.B. mit diesem Befehl

    hyperion-v4l2 --video-standard "NTSC" --width 720 --crop-right 4 --crop-top 4 --crop-bottom 5 --size-decimator 2 --frame-decimator 1 --skip-reply --signal-threshold 0.00 --pixel-format rgb32 </dev/null >/dev/null 2>&1 &

  • so habe es ausprobiert... das ist erstmal der auszug aus putty

    lpi@raspberrypi ~ $ lsusb
    Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
    Bus 001 Device 004: ID 05e1:0408 Syntek Semiconductor Co., Ltd STK1160 Video Captu re Device
    pi@raspberrypi ~ $ ls /dev
    autofs loop0 network_latency ram4 stdout tty21 tty36 tty50 tty8 vcsa
    block loop1 network_throughput ram5 tty tty22 tty37 tty51 tty9 vcsa1
    btrfs-control loop2 null ram6 tty0 tty23 tty38 tty52 ttyAMA0 vcsa2
    bus loop3 ppp ram7 tty1 tty24 tty39 tty53 ttyprintk vcsa3
    cachefiles loop4 ptmx ram8 tty10 tty25 tty4 tty54 uinput vcsa4
    char loop5 pts ram9 tty11 tty26 tty40 tty55 urandom vcsa5
    console loop6 ram0 random tty12 tty27 tty41 tty56 vc-cma vcsa6
    cpu_dma_latency loop7 ram1 raw tty13 tty28 tty42 tty57 vchiq video0
    disk loop-control ram10 root tty14 tty29 tty43 tty58 vc-mem xconsole
    fb0 MAKEDEV ram11 shm tty15 tty3 tty44 tty59 vcs zero
    fd mapper ram12 snd tty16 tty30 tty45 tty6 vcs1
    full mem ram13 sndstat tty17 tty31 tty46 tty60 vcs2
    fuse mmcblk0 ram14 spidev0.0 tty18 tty32 tty47 tty61 vcs3
    input mmcblk0p1 ram15 spidev0.1 tty19 tty33 tty48 tty62 vcs4
    kmsg mmcblk0p2 ram2 stderr tty2 tty34 tty49 tty63 vcs5
    log net ram3 stdin tty20 tty35 tty5 tty7 vcs6
    pi@raspberrypi ~ $

    Und das meine neue Config.. momentan leuchten nur die ersten oder erste Led blau
    http://workupload.com/file/BDCmg7sV

    Einmal editiert, zuletzt von Schmello (8. Januar 2015 um 20:14)

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!