Hallo Freunde,
ich versuche nun schon seit 3 Tagen meinen Raspberry Pi Modell 3 zu einem Fax-Server umzufunktionieren. Dazu benutze ich das Trendnet TFM-561U USB Modem in Kombination mit HylaFax.
Nach der folgenden Anleitung bin ich vorgegangen:
http://www.stahn.eu/2015/12/24/der…-als-faxserver/
Soweit funktioniert auch das Senden von Faxen ohne weitere Probleme, jedoch nimmt mein Fax-Server keine Faxe entgegen. Wenn man die entsprechende Telefonnummer anruft, dann hört man zwar das Freizeichen, aber der Anruf wird von dem Gerät nicht angenommen.
Wenn man das Annehmen des Anrufes mit dem Befehl "faxanswer ttyACM0" erzwingt, dann wird der Anruf angenommen und Fax wird erfolgreich empfangen, jedoch passiert dies nicht automatisch. Dabei müsste er das laut Config nach einem Freizeichen tun.
Hier meine config.ttyACM0:
# $Id$
#
# Configuration for a Rockwell/Conexant K56 Class 1.0 modem using
# the RCV56DPF and similar chipsets. These chipsets are generally
# flash- upgradable and appear on ISA as well as PCI. They
# support "Class 1.0" which means that they have "adaptive receive"
# (AT+FAR=1), but not V.34.
#
# Comtrol RocketModem II/III/IV
# MultiTech MT5600ZDX
# Zoltrix FMVSP56i3
#
#
CountryCode: 49
AreaCode: 0211
FAXNumber: +49211******
LongDistancePrefix: 049
InternationalPrefix: 00
DialStringRules: etc/dialrules.europe
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0644
LogFileMode: 0644
DeviceMode: 0644
RingsBeforeAnswer: 1
SpeakerVolume: low
GettyArgs: "-h %l dx_%s"
LocalIdentifier: ************
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1.0 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
# With the RocketModem IV (and possibly III) you may need to use a much
# higher ModemRate than 19200 because, apparently, it suffers from potential
# buffer underrun problems. Fortunately, it doesn't have buffer overflow
# issues, and so using 115200 should work (both rtscts and xonxoff test good).
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
Class1AdaptRecvCmd: AT+FAR=1 # reports carrier detection mismatches
Alles anzeigen
faxgetty läuft wohl im Hintergrund:
root@raspberrypi:/home/pi# ps -ef |grep fax
uucp 905 1 0 15:29 ? 00:00:00 /usr/sbin/faxq
uucp 909 1 0 15:29 ? 00:00:00 /usr/sbin/hfaxd -d -i 4559
uucp 924 1 0 15:29 ? 00:00:00 /usr/sbin/faxgetty -D ttyACM0
Ich habe mich mittlerweile kaputtgegoogelt, aber immer noch keinen möglichen Lösungsansatz gefunden. Evtl. könnte mir einer von Euch ein paar Tipps geben. Danke im Voraus.
Schöne Grüße,
Vincent