Hallo,
Eth0 wird nicht unter ifconfig angezeigt. Ich kann auch über LAN keine Verbindung zum Pi aufbauen. Woran kann das liegen. Achja die Wlanverbindung läuft.
Hallo,
Eth0 wird nicht unter ifconfig angezeigt. Ich kann auch über LAN keine Verbindung zum Pi aufbauen. Woran kann das liegen. Achja die Wlanverbindung läuft.
Eth0 wird nicht unter ifconfig angezeigt? Schau mal ob du hier fündig wirst!
Eth0 wird nicht unter ifconfig angezeigt. Ich kann auch über LAN keine Verbindung zum Pi aufbauen. Woran kann das liegen. Achja die Wlanverbindung läuft.
Wie sind die Ausgaben von:
?
ZitatAlles anzeigen
auto loiface lo inet loopback
allow-hotplug eth0
iface eth0 inet static
address 192.168.178.111
netmask 255.255.255.0
gateway 192.168.178.1allow-hotplug wlan0
iface wlan0 inet static
address 192.168.178.222
netmask 255.255.255.0
gateway 192.168.178.1
wpa-driver wext
wpa-ssid xxx
wpa-ap-scan 1
wpa-proto RSN
wpa-pairwise CCMP
wpa-group CCMP
wpa-key-mgmt WPA-PSK
wpa-psk "xxx"
#wpa-roam /etc/wpa_supplicant/wpa_supplicant.confiface default inet dhcp
Zitat
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.178.1 0.0.0.0 UG 0 0 0 wlan0
192.168.178.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0
ZitatAlles anzeigen
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:700 (700.0 B) TX bytes:700 (700.0 B)wlan0 Link encap:Ethernet HWaddr xxx
inet addr:192.168.178.222 Bcast:192.168.178.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:122696 errors:0 dropped:2748 overruns:0 frame:0
TX packets:113454 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:15014956 (14.3 MiB) TX bytes:13388672 (12.7 MiB)
ZitatAlles anzeigen
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether xxx brd ff:ff:ff:ff:ff:ff
inet 192.168.178.222/24 brd 192.168.178.255 scope global wlan0
valid_lft forever preferred_lft forever
Code Alles anzeigenauto lo iface lo inet loopback allow-hotplug eth0 iface eth0 inet static address 192.168.178.111 netmask 255.255.255.0 gateway 192.168.178.1 allow-hotplug wlan0 iface wlan0 inet static address 192.168.178.222 netmask 255.255.255.0 gateway 192.168.178.1 wpa-driver wext wpa-ssid xxx wpa-ap-scan 1 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk "xxx" #wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp
Versuch mal mit:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
address 192.168.178.9
netmask 255.255.255.0
gateway 192.168.178.1
allow-hotplug wlan0
iface wlan0 inet static
address 192.168.178.222
netmask 255.255.255.0
gateway 192.168.178.1
wpa-driver wext
wpa-ssid xxx
wpa-ap-scan 1
wpa-proto RSN
wpa-pairwise CCMP
wpa-group CCMP
wpa-key-mgmt WPA-PSK
wpa-psk "xxx"
#wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
#iface default inet dhcp
Alles anzeigen
D. h. mit "auto eth0" und einer statischen IP-Adresse für eth0, außerhalb des DHCP-Pools der FritzBox.
ich habe das jetzt geändert, jedoch ohne erfolg
ich habe das jetzt geändert, jedoch ohne erfolg[/font]
Nur geändert, oder auch das Netzwerk des Pi neu gestartet?
hab den pi direkt neu gestartet
hab den pi direkt neu gestartet
Versuch mal:
Zitat
SIOCSIFADDR: No such device
eth0: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
ZitatAlles anzeigen
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:3 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:195 (195.0 B) TX bytes:195 (195.0 B)wlan0 Link encap:Ethernet HWaddr xxx
inet addr:192.168.178.222 Bcast:192.168.178.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17590 errors:0 dropped:809 overruns:0 frame:0
TX packets:14306 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2339410 (2.2 MiB) TX bytes:1921172 (1.8 MiB)
Ich denke, dann stimmt mit dem Treiber etwas nicht, oder es könnte evtl. auch ein Hardwaredefekt sein.
EDIT:
Wie sind die Ausgaben von:
?
Wenn es sich um ein Treiberproblem handelt, wie kann ich den treiber neu installiern?
Wenn es ...
Wie sind jetzt die Ausgaben von:
?
ich spiel erstmal ein neues image auf und prüf ob die lan karte defekt ist. und probiere das nacher dann mal
ich spiel erstmal ein neues image auf und prüf ob die lan karte defekt ist. und probiere das nacher dann mal
Das wäre schon wichtig, das jetzt zu probieren (d. h. vor dem neuen image).
So die Lan Modul ist auf jedenfall noch in Ordnung.
Zitat
Linux raspberrypi 3.12.30+ #717 PREEMPT Fri Oct 17 18:46:31 BST 2014 armv6l GNU/Linux
ZitatAlles anzeigen
Module Size Used by
tusbd 45876 4
snd_bcm2835 19584 0
dvb_usb_af9005_remote 2174 3
snd_soc_bcm2708_i2s 6210 0
regmap_mmio 2818 1 snd_soc_bcm2708_i2s
snd_soc_core 127849 1 snd_soc_bcm2708_i2s
snd_compress 8259 1 snd_soc_core
regmap_i2c 1661 1 snd_soc_core
snd_pcm_dmaengine 5505 1 snd_soc_core
regmap_spi 1913 1 snd_soc_core
dvb_usb_af9005 24291 2147483647
evdev 10661 0
snd_pcm 83845 3 snd_bcm2835,snd_soc_core,snd_pcm_dmaengine
dvb_usb 17822 1 dvb_usb_af9005
snd_page_alloc 5132 1 snd_pcm
joydev 9257 0
snd_seq 55484 0
dvb_core 93748 1 dvb_usb
snd_seq_device 6469 1 snd_seq
rc_core 17576 1 dvb_usb
snd_timer 20998 2 snd_pcm,snd_seq
8192cu 550797 0
leds_gpio 2079 0
led_class 4118 1 leds_gpio
snd 62252 7 snd_bcm2835,snd_soc_core,snd_timer,snd_pcm,snd_s eq,snd_seq_device,snd_compress
ZitatAlles anzeigen
[ 0.000000] Machine: BCM2708
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708.boardrev=0xf bcm2708.serial=0xc43c6cef smsc95xx.macaddr=B8:27:EB:3C:6C:EF sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
[ 0.029482] bcm2708.uart_clock = 0
[ 0.031693] bcm2708_vcio: mailbox at f200b880
[ 1.040911] bcm2708_dma: DMA manager at f2007000
[ 1.045656] bcm2708_gpio: bcm2708_gpio_probe c05f1f10
[ 1.298672] BCM2708FB: allocated DMA memory 5bc00000
[ 1.303721] BCM2708FB: allocated DMA channel 0 @ f2007000
[ 1.324923] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driver
[ 1.412641] usbcore: registered new interface driver smsc95xx
[ 1.929244] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.935460] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 1.944111] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 1.990878] usb usb1: SerialNumber: bcm2708_usb
[ 3.105154] smsc95xx v1.0.4
[ 3.173748] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:3c:6c:ef
[ 3.999314] input: http://www.irfmedia.com P-05R UIR_V3A as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2.5/1-1.2.5:1.0/input/input0
[ 4.026801] hid-generic 0003:0755:2026.0001: input,hidraw0: USB HID v1.10 Keyboard [http://www.irfmedia.com P-05R UIR_V3A] on usb-bcm2708_usb-1.2.5/input0
[ 4.076851] input: http://www.irfmedia.com P-05R UIR_V3A as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2.5/1-1.2.5:1.1/input/input1
[ 4.117415] hid-generic 0003:0755:2026.0002: input,hidraw1: USB HID v1.10 Mouse [http://www.irfmedia.com P-05R UIR_V3A] on usb-bcm2708_usb-1.2.5/input1
[ 21.172991] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 27.652194] smsc95xx 1-1.1:1.0 eth0: unregister 'smsc95xx' usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet
[ 27.652275] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Code[ 3.105154] smsc95xx v1.0.4 [ 3.173748] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:3c:6c:ef [ 3.999314] input: www.irfmedia.com P-05R UIR_V3A as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2.5/1-1.2.5:1.0/input/input0 [ 4.026801] hid-generic 0003:0755:2026.0001: input,hidraw0: USB HID v1.10 Keyboard [www.irfmedia.com P-05R UIR_V3A] on usb-bcm2708_usb-1.2.5/input0 [ 4.076851] input: www.irfmedia.com P-05R UIR_V3A as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2.5/1-1.2.5:1.1/input/input1 [ 4.117415] hid-generic 0003:0755:2026.0002: input,hidraw1: USB HID v1.10 Mouse [www.irfmedia.com P-05R UIR_V3A] on usb-bcm2708_usb-1.2.5/input1 [ 21.172991] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 27.652194] smsc95xx 1-1.1:1.0 eth0: unregister 'smsc95xx' usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet [ 27.652275] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
In der Ausgabe von dmesg, fehlt aber folgende Zeile (oder gleichwertig):
... oder hast Du nicht alles gepostet oder habe ich das übersehen?
war ganz unten aber hier nochmal:
Zitat
[ 21.172991] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 27.652194] smsc95xx 1-1.1:1.0 eth0: unregister 'smsc95xx' usb-bcm2708_usb-1.1, smsc95xx U SB 2.0 Ethernet
[ 27.652275] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
mehr wurde mir nicht ausgegben wenn du das nicht meinst
Mal "dumm" gefragt (nur, damit wir dass als Fehlerquelle ausschließen können):
Hast du mal das LAN-Kabel kontrolliert bzw. ausgetauscht?
Leuchtet der LNK Anschluss am Routerport auf, wenn du das Kabel einsteckst?
Mfg, Zen
Lankabel ist OK. Mit einem anderen Image funktioniert es ja.
Mit einem anderen Image funktioniert es ja.
Auf dem gleichen PI (d. h. identische Hardware), aber das andere Image auf einer anderen SD-Karte? Hast Du evtl. mehrere PIs oder hast Du das Image das nicht funktioniert, evtl. auf einem anderen PI, in der Vergangenheit benutzt?
Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!