Bildschirm Schwarz

Heute ist Stammtischzeit:
Jeden Donnerstag 20:30 Uhr hier im Chat.
Wer Lust hat, kann sich gerne beteiligen. ;)
  • http://www.ebay.de/itm/121213914478
    Universal 4,3" TFT LCD Monitor mit Composite Eingang

    Hallo miteinander,
    Ich verwende obigen Monitor aber mit rspbian auf sd karte wird auf dem Monitor nichts angezeigt beim booten.. verwende ich selbe jedoch raspbmc auf einer anderen sd karte zum booten erfolgt eine Anzeige.. woran kann dies liegen?
    sd karte mit raspbian - mit Pc Bildschirm ist Bootscreen sichtbar.. also ist SD Karte in Ordnung
    Danke für Tips!

    Bernd

  • Beide Systeme händeln den Umgang mit HDMI etwas unterschiedlich. Bei Raspbian kannst Du in der config.txt den RasPi zwingen einen bestimmten Ausgang zu nutzen. Tust Du das nicht, kann es passieren das er zwar kein HDMI erkennt und trotzdem den analogen Ausgang nicht benutzt.

    Noch eine Frage: Welchen RasPi nutzt Du? Bzw. nutzt Du den richtigen Adapter?


  • Beide Systeme händeln den Umgang mit HDMI etwas unterschiedlich. Bei Raspbian kannst Du in der config.txt den RasPi zwingen einen bestimmten Ausgang zu nutzen.

    Hallo

    zu diesem Abschnitt habe ich das hier rausgesucht.
    von http://elinux.org/RPiconfig

    hdmi_ignore_hotplug=1 Use composite mode even if HDMI monitor is detected

    Dann kannst du aber kein HDMI mehr benutzen bis du das obrig genannte zurücksetzt.

    mfg


    nebenbei: der monitor hat 2 eingänge (gelb & weiß)
    beide schon ausprobiert?

    Einmal editiert, zuletzt von Gamefreak23 (29. April 2015 um 14:32)

  • hallo zusammen,
    erstmal herzlichen dank für die hilfe.. !
    super!
    - ich habe gerade den weissen eingang ausprobiert, selbes problem wie beim gelben stecker.. schirm schwarz.
    leider finde ich keine config.txt..
    noobs..
    ich finde nur folgende dateien:

    Verzeichnis von j:\os\Raspbian

    27.04.2015 23:31 <DIR> .
    27.04.2015 23:31 <DIR> ..
    27.04.2015 23:30 9.880.724 boot.tar.xz
    27.04.2015 23:30 439 flavours.json
    27.04.2015 23:30 357 os.json
    27.04.2015 23:30 445 partitions.json
    27.04.2015 23:30 414 partitions.json~
    27.04.2015 23:30 420 partition_setup.sh
    27.04.2015 23:30 1.662 Raspbian.png
    27.04.2015 23:30 2.857 Raspbian_-_Boot_to_Scratch.png
    27.04.2015 23:30 2.235 release_notes.txt
    27.04.2015 23:30 739.973.220 root.tar.xz
    27.04.2015 23:30 <DIR> slides_vga
    10 Datei(en), 749.862.773 Bytes
    3 Verzeichnis(se), 77.299.712 Bytes frei

    Thx for Infos.
    bernd

  • Du verwendest also eine durch noobs installierte Raspbian Version, oder?

    Mist, ich hätte die Überschrift lesen sollen! :wallbash:

    Aus der Noobs Hilfe:

    By default, NOOBS will output over HDMI at your display’s preferred resolution, even if no HDMI display is connected. If you do not see any output on your HDMI display or are using the composite output, press 1, 2, 3 or 4 on your keyboard to select HDMI preferred mode, HDMI safe mode, composite PAL mode or composite NTSC mode respectively.

    If you don't have a keyboard, you can still change the display mode used by NOOBS through editing the recovery.cmdline file in the root NOOBS directory prior to first boot and appending the following argument:

    display=<display mode number> (e.g. display=1 or display=3)

    Auf Deutsch: Drücke die Taste 3 (NTSC) oder editiere die recovery.cmdline wie folgt:

    Code
    display=3
  • thx!
    INSTRUCTIONS-README
    hatte ich gesehen..
    dort steht bei mir jedoch:
    ..
    5. Insert the SD card into your Pi and connect the power supply.

    Your Pi will now boot into NOOBS and should display a list of operating systems that you can choose to install.
    If your display remains blank, you should select the correct output mode for your display by pressing one of the following number keys on your keyboard:
    1. HDMI mode - this is the default display mode.
    2. HDMI safe mode - select this mode if you are using the HDMI connector and cannot see anything on screen when the Pi has booted.
    3. Composite PAL mode - select either this mode or composite NTSC mode if you are using the composite RCA video connector.
    4. Composite NTSC mode

    If you are still having difficulties after following these instructions, then please visit the Raspberry Pi Forums ( http://www.raspberrypi.org/forums/ ) for support.

    ..
    also nichts von editing recovery.cmdline..:>))

    ich hab es jetzt mal editiert, werde mal schauen ob es funktioniert..
    hatte das noch ausprobiert mit den tasten, hat aber nicht funktioniert.. wusste auch nicht genau ob 3 oder 4 und zu welchem Zeitpunkt drücken.. hab mehrmals ausprobiert ohne Erfolg.
    ich teste jetzt mal nach dem Editieren.

    display=3
    habe ich in die .cmdline hinter dem einzigen anderen eintrag hinzugefügt als neuen string unterhalb.
    Bootet aber wieder in einen schwarzen Bildschirm, egal ob am weissen oder gelben Stecker.
    USB HUB an usb angeschlossen dort Tastatur und Maus angeschlossen.
    Strom USB vom Bildschirm direkt am zweiten usb des pi.
    am weissen Stecker flackert Bildschirm ganz kurz beim Start.

    By the way, wo kann ich denn raspbian direkt downloaden, als image, ohne Noobs zu nutzen.. dann könnte ich es damit mal versuchen denn dort müsste ja die config.txt vorliegen und editierbar sein?

    :rolleyes:

    Einmal editiert, zuletzt von bernd67 (29. April 2015 um 23:43)

  • neuer versuch mit raspbian, downloaded wheezy von der angegebenen seite,
    image auf sd geimaged...

    config.txt zu finden jetzt:

    # For more options and information see
    # http://www.raspberrypi.org/documentation/…n/config-txt.md
    # Some settings may impact device functionality. See link above for details

    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1

    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    #disable_overscan=1

    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16

    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720

    # uncomment if hdmi display is not detected and composite is being output
    #hdmi_force_hotplug=1

    # uncomment to force a specific HDMI mode (this will force VGA)
    #hdmi_group=1
    #hdmi_mode=1

    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2

    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    #config_hdmi_boost=4

    # uncomment for composite PAL
    #sdtv_mode=2

    #uncomment to overclock the arm. 700 MHz is the default.
    #arm_freq=800


    was genau ist jetzt einzustellen?
    ich denke hier die # wegmachen?:
    # uncomment if hdmi display is not detected and composite is being output
    #hdmi_force_hotplug=1

    gruss bernd

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!