Iso oder img werden nicht abgespielt aber die VOB laufen

  • Ich habe einen Raspberry B3 mit debian jessie (ARM 7). Habe die license keys erfolgreich registriert.
    Kontrolle im Terminal:

    pi@raspi:~ $ vcgencmd codec_enabled WVC1
    WVC1=enabled

    pi@raspi:~ $ vcgencmd codec_enabled MPG2
    MPG2=enabled

    Hier ist mein config.txt:
    # For more options and information see
    # http://www.raspberrypi.org/documentation/…n/config-txt.md
    # Some settings may impact device functionality. See link above for details

    # uncomment if you get no picture on HDMI for a default "safe" mode
    #hdmi_safe=1

    # uncomment this if your display has a black border of unused pixels visible
    # and your display can output without overscan
    disable_overscan=1

    # uncomment the following to adjust overscan. Use positive numbers if console
    # goes off screen, and negative if there is too much border
    #overscan_left=16
    #overscan_right=16
    #overscan_top=16
    #overscan_bottom=16

    # uncomment to force a console size. By default it will be display's size minus
    # overscan.
    #framebuffer_width=1280
    #framebuffer_height=720

    # uncomment if hdmi display is not detected and composite is being output
    #hdmi_force_hotplug=1

    # uncomment to force a specific HDMI mode (this will force VGA)
    hdmi_group=1
    hdmi_mode=4

    # uncomment to force a HDMI mode rather than DVI. This can make audio work in
    # DMT (computer monitor) modes
    #hdmi_drive=2

    # uncomment to increase signal to HDMI, if you have interference, blanking, or
    # no display
    # config_hdmi_boost=4

    # uncomment for composite PAL
    #sdtv_mode=2

    decode_MPG2=0x2d6c16e
    decode_WVC1=0x8a4e2c2b

    #uncomment to overclock the arm. 700 MHz is the default.
    arm_freq=700

    # Uncomment some or all of these to enable the optional hardware interfaces
    #dtparam=i2c_arm=on
    #dtparam=i2s=on
    dtparam=spi=off

    # Uncomment this to enable the lirc-rpi module
    dtoverlay=lirc-rpi

    # Additional overlays and parameters are documented /boot/overlays/README

    # Enable audio (loads snd_bcm2835)
    dtparam=audio=on
    gpu_mem=128

    Wenn ich nun die eine iso oder img Datei aufrufe, bekomme ich nur das Menu. Wenn ich dann Film starten wähle,
    höre ich den Ton des Filmes, aber das Menu bleibt.

    Rufe ich mir im Datei-Manager die Datei auf und gehe in die VIDEO_TS kann ich die VOB ohne Ruckler und Tonprobleme abspielen. AC3 5.1 oder DTS werden in meinem Soundsystem einwandfrei abgespielt.

    Unter dem alten Openelec und einem Raspberry 2 gab es keine Probleme ISO, IMG liefen super. Dann kam unter openelec "Isengard" danach lief gar nichts mehr, Filme blieben stehen, der Raspberry stürzte permanent ab. Gut, habe dann den Raspi 3 geholt aber unter OpenElec mit "Isengard" das gleiche Problem. Bei Debian Jessie lief alles sofort super bis auf iso und img.

    Meine Filme liegen auf 5 HDD die an einem UBUNTU 12.04. LTS Rechner gemounted sind. nfs Kernel Server läuft auch.
    Beide Möglichkeiten habe ich ebenfalls ausprobiert: iso und img funktionieren weder unter SMB noch unter nfs.

    Wer kann da helfen?

    Ciao
    Roberto

    Einmal editiert, zuletzt von roberto16900 (21. September 2016 um 18:16)

  • Iso oder img werden nicht abgespielt aber die VOB laufen? Schau mal ob du hier fündig wirst!

  • openelec IST TOT! Es wird kaum noch weiterentwickelt ! Da alle entwickler abgesprungen sind! Deswegen empfehle ich dir LibreElec zu nutzen.
    Dort probierts du es dann erneut aus.


    Mfg

    Wenn's brennt 112 hilft weiter!


  • openelec IST TOT! Es wird kaum noch weiterentwickelt ! Da alle entwickler abgesprungen sind! Deswegen empfehle ich dir LibreElec zu nutzen.
    Dort probierts du es dann erneut aus.


    Mfg

    Ich benutzte Openelec jetzt habe ich Kodi über Debian installiert und habe das o.a. Problem. Es könnte vielleicht am Netzteil liegen,
    denn die rote LED erlischt sehr oft, das bedeutet ich liege unter 4,6 V. Werde das morgen mit einem 3000 mA und 5,1 V Netzteil ausprobieren und dann berichten.
    Danke
    Ciao
    Roberto :D

  • :danke_ATDE:


    openelec IST TOT! Es wird kaum noch weiterentwickelt ! Da alle entwickler abgesprungen sind! Deswegen empfehle ich dir LibreElec zu nutzen.
    Dort probierts du es dann erneut aus.


    Mfg

    :danke_ATDE:
    Hi
    Super Tipp alles läuft wie am Schnürchen. Hätte mir viel Arbeit ersparen können wenn ich es schon vorher gewusst hätte.

    Danke noch einmal

    Ciao
    Roberto

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!