Überwachungskamera Nachbauen

L I V E Stammtisch ab 20:30 Uhr im Chat
  • Hallo Leute,

    ich bin neu auf dem Gebiet des Raspberry´s und schon sehr am verzweifeln. Ich hänge nun schon den ganzen Tag an mehreren Applikation und immer bleibe ich an irgendwas hängen :(

    Aktuell möchte ich gerne das folgende Projekt "nachbauen":
    http://www.codeproject.com/Articles/66551…eillance-camera

    Leider scheitere ich wohl schon an den Basics ... ich bin die ganze Anleitung brav durch gegangen doch bei folgendem Befehl: [font="Menlo"]tar zxvf motion-mmal.tar.gz[/font]

    [font="Menlo"]pi@raspberrypi /tmp $ tar zxvf motion-mmal.tar.gz[/font]
    [font="Menlo"]tar (child): motion-mmal.tar.gz: Cannot open: No such file or directory[/font]
    [font="Menlo"]tar (child): Error is not recoverable: exiting now[/font]
    [font="Menlo"]tar: Child returned status 2[/font]
    [font="Menlo"]tar: Error is not recoverable: exiting now [/font]

    Kann mir jemand sagen was ich falsch mache? Ich habe den Text sogar 1 zu 1 aus dem Quellcode des "Erfinders" kopiert, also scheiden auch Tippfehler aus ...

    Ich weiß nicht weiter, bitte helft mir.

    Beste Grüße

    Steffen

  • tar sagts doch ganz klar:

    tar (child): motion-mmal.tar.gz: Cannot open: No such file or directory

    Das File existiert nicht !

    Im Directory ls -l aufrufen und nachsehen, ob es das File dort gibt.
    Wenn nicht, das File beschaffen.

    Wenn es etwas gibt was aehnlich heisst, koennte es ein Tippfehler sein.

    Die Gross-Kleinschreibung ist unter Linux uebrigens wichtig ...

  • Hallo Steffen,

    Du hast da keinen Tipp- sondern einen Denkfehler drin ;)
    Hast Du den wget gemacht und wenn ja, dann wie genau?
    Tar sagt Dir ganz klar: sorry, das Archiv finde ich nicht im aktuellen Verzeichnis.
    Was also könnte der Fehler sein?


    cu,
    -ds-

  • Herzlichen Dank, habe es nochmals mehrfach versucht, kam aber nach dem vermeintlichen download immer wieder dieselbe Fehlermeldung, obwohl die Datei körperlich vorhanden war. Habe mir dann die betreffende Datei von meinem Mac herunter geladen und mittels USB Stick auf den RAspberry kopiert, dann hat as zumindest funktioniert.

    Habe nun weiter gemacht wie beschrieben, doch nach dem Reboot funktioniert die Motion Funktion trotzdem nicht :(.

    Wie bekomme ich raus was ich falsch gemacht habe? Wo kann ich Fehlermeldungen o.ä. rauslesen?

    Herzlichen Dank auch noch für die Infos bezüglich der Groß und Kleinschreibung! Das wußte ich nicht.

    Beste Grüße

    Steffen

  • Moin,

    läuft den 'motion' sprich wurde es beim start mit gestartet? -> ps -eaf | grep -i motion

    Denn dass schien mir in der Anleitung zu fehlen, beim kurzen drüberfliegen

    Gruß Lunepi

    Noch den Frage, ein Bild von der Kamera bekommst du? Außerdem hast du laut Anleitung das logfile angelegt motion.log - sagt das was hilfreiches?

    --
    man ist das System-Anzeigeprogramm für die Handbuchseiten von Linux.

    Einmal editiert, zuletzt von Lunepi (14. Februar 2014 um 14:19)


  • Habe nun weiter gemacht wie beschrieben, doch nach dem Reboot funktioniert die Motion Funktion trotzdem nicht :(.
    Wie bekomme ich raus was ich falsch gemacht habe? Wo kann ich Fehlermeldungen o.ä. rauslesen?

    Moin,

    hast Du die RPi Kamera "freigeschaltet" z. B. raspi-config?

    Die Fehlermeldungen werden in der Regel unter /var/log/...abgelegt, abhängig davon welcher path/Datei in der Konfigurationsdatei zum loggen angegeben wurde.
    Nach der Anleitung:
    logfile /tmp/motion.log

    Hilfreich wäre auch welcher Befehl abgesetzt wird und was dann auf der Console ausgegeben wird.

    Bye

    Jürgen


  • Nach der Anleitung:
    logfile /tmp/motion.log

    Hilfreich wäre auch welcher Befehl abgesetzt wird und was dann auf der Console ausgegeben wird.

    Bye

    Jürgen


    wenn ich den oberen Tag eingebe kommt die Meldung: "bash: logfile: command not found"

    Und ja, die Kamera ist freigeschaltet. Ich kann auch Bilder mittels raspistill machen. Ebenso funktioniert die permanente Aufnahme nach Anleitung von Jan Karres. Es liegt also definitiv "nur" an einem Script/Programmierfehler ...

    Ich kann Dir leider nicht sagen welcher Befehl wo abgesetzt wurde, da ich das ganze quasi nur abgeschrieben habe ... malen nach Zahlen nach der Anleitung ...

    @ lunepi:
    [font="Tahoma, Verdana, Arial, sans-serif"] -> ps -eaf | grep -i motion[/font]

    [font="Tahoma, Verdana, Arial, sans-serif"]Wo muss das hin? In die Motion?[/font]

    [font="Tahoma, Verdana, Arial, sans-serif"]Besten Dank schonmal. [/font]

    [font="Tahoma, Verdana, Arial, sans-serif"]Steffen[/font]


  • wenn ich den oberen Tag eingebe kommt die Meldung: "bash: logfile: command not found"

    Hmmmmm,

    das musst Du schon anschauen, z. B. neue Console/Terminal und dann:


    Code
    sudo tail -f /tmp/motion.log


    Dann das Programm / Script in einer weiteren Console starten und live sehen was abgeht.

    Die Ausgabe von tail kannst Du mit Strg + C beenden.

    Deine ersten Gehversuche mit Linux ? ;)

    Bye

    Jürgen


    PS.:

    Code
    ps -eaf | grep -i motion

    Ist der Befehl die (laufenden) Prozesse nach dem Prozessnamen motion zu suchen., wobei die Ausgabe mit ... grep -i motion zu ignorieren ist, da es sich um den Suchprozess handelt.

    Einmal editiert, zuletzt von rpivpn (14. Februar 2014 um 17:56)

  • Herzlichen Dank für die Hilfe und das Verständnis! Ja, wie man sieht meiner ersten Gehversuche, und so fasziniert und begeistert ich von diesem System bin, so verzweifelt bin ich auf der anderen Seite auch ... der Sprung ins kalte Wasser was doch nicht so sonderlich schlau ...

    Hier mein Ergebnis:

    [font="Menlo"]pi@raspberrypi ~ $ sudo tail -f /tmp/motion.log[/font]
    [font="Menlo"][1] [ALR] [VID] [Feb 14 16:17:42] mmalcam_start: MMAL Camera using video capture[/font]
    [font="Menlo"][1] [ERR] [ENC] [Feb 14 18:43:21] ffmpeg_open: url_fopen - error opening file /home/pi/01-20140214184321.avi ... check access rights to target directory: [/font]
    [font="Menlo"][1] [ERR] [EVT] [Feb 14 18:43:21] event_ffmpeg_newfile: ffopen_open error creating (new) file [/home/pi/01-20140214184321.avi]: [/font]
    [font="Menlo"][1] [ERR] [ALL] [Feb 14 18:43:21] myfopen: Error opening file /home/pi/01-20140214184320-00.jpg with mode w: [/font]
    [font="Menlo"][1] [ERR] [ALL] [Feb 14 18:43:21] put_picture: Can't write picture to file /home/pi/01-20140214184320-00.jpg - check access rights to target directory[/font]
    [font="Menlo"]Thread is going to finish due to this fatal error: [/font]
    [font="Menlo"][1] [ERR] [ALL] [Feb 14 18:43:21] myfopen: Error opening file /home/pi/01-20140214184320-01.jpg with mode w: [/font]
    [font="Menlo"][1] [ERR] [ALL] [Feb 14 18:43:21] put_picture: Can't write picture to file /home/pi/01-20140214184320-01.jpg - check access rights to target directory[/font]
    [font="Menlo"]Thread is going to finish due to this fatal error: [/font]
    [font="Menlo"][1] [ALR] [VID] [Feb 14 18:43:21] MMAL Camera cleanup[/font]

    [font="Menlo"]Böhmische Dörfer :stumm::no_sad:[/font]

    [font="Menlo"]Diesen Befehl habe ich über ssh an meinem Macbook [/font][font="Menlo"]eingegeben. Nur was meinst Du anderer Console anschauen? Was soll sich tun wenn ich auf dem Raspberry eine Console öffne, während ich auf dem Macbook per ssh Zugriff den Befehl ausführe?[/font]

  • [font="Menlo"]pi@raspberrypi~ $ ls /home/pi[/font]
    [font="Menlo"]Desktop index.html.1 motion-mmal.tar.gz     ocr_pi.png    test.jpg[/font]
    [font="Menlo"]aufnahme.jpeg index.html.2 motion-mmal.tar.gz.1 picam         video[/font]
    [font="Menlo"]aufnahme.jpg   motion motion-mmal.tar.gzold python_games[/font]
    [font="Menlo"]index.html motion-mmal motion-mmalcam.conf rpi-update[/font]

    [font="Menlo"]Dieser Befehl war wohl ähnlich wie Dir im guten alten DOS ...[/font]

    [font="Menlo"]:bravo2::bravo2::bravo2::bravo2:
    [/font]

    [font="Menlo"]Die motion-mmal.tar.gz.1 war die Datei die ich zweimal runter geladen hab, weil sie ja angeblich nicht da war ...[/font]

    [font="Menlo"]Die [font="Menlo"]motion-mmal.tar.gzold war die allererste die ich runter geladen habe, die ja ebenfalls nicht gefunden wurde, da ich sie aber nicht löschen wollte, habe ich sie schlicht und ergreifend umbenannt, und somit (davon gehe ich zumindest aus) für das System unbrauchbar gemacht[/font][/font]

    [font="Menlo"][font="Menlo"]Die rot markierte motion-mmal.tar.gz ist die von mir Manuel herunter geladene, und aufgespielte [/font]Datei.[/font]

    [font="Menlo"]aufnahme.jpeg, Aufnahme.jpg sowie test.jpg waren die Testaufnahmen die ich mit raspistill gemacht habe[/font]

  • Moin,

    damit wären schon mal 2 Dinge geklärt:
    pi darf auf seinen path zugreifen :angel:, war auch nicht anders zu erwarten.

    und die ...avi Datei ist nicht vorhanden.

    Also suchen wir diese mal, vielleicht wurde sie ja nur /?unbekannt?/ gespeichert:

    Code
    sudo find / -name *.avi
  • OK,

    somit sollte auch nix zugemüllt worden sein.


    Ich vermute motion läuft als daemon ohne Zugriff/Schreibrecht auf /home/pi/.
    Rechte ändern oder einen Ordner wählen für den Schreibrechte bestehen.

    Die motion.conf bitte:

    Wie Du diese findest, find........

    Öffen und bearbeiten mit sudo nano /?/motion.conf

    /?/ ist der path unter der diese gespeichert ist (siehe Ausgabe von find)

    Bye

    Jürgen

  • Hallo Jürgen,

    die motion.conf befindet sich in /etc/ gemäß Anleitung. Nur finde ich im File Manager keinen Ordner namens etc, er ist aber vorhanden, denn die motion.conf kann ich aufrufen.

    Nur wo gebe ich da den Ordner an wo er speichern soll?

  • Moin,

    was steht in der:

    sudo nano /etc/default/motion

    und der ( nach daemon und target_dir suchen)

    sudo nano /etc/motion/motion.conf

    Welcher Port (webcam_port)?

    Sofern die Überwachung/Aufnahme unentwegt läuft ruinierst Du dir die SD, besser ist es in ein RAMDRIVE zu schreiben.

    Bye

    Jürgen

  • Hallo Jürgen,

    in der motion.conf ist der daemon auf "on"

    "target_dir" sowie "webcam_port" findet er in der motion.conf jedoch nicht ...

    wenn die Aufnahme überhaupt starten würde, wäre mein Problem ja gelöst ... wohin er dann speichert ist ja dann der nächste Step ...

    Irgendwie ist das ziemlich frustrierend :(

  • Doch, dameon steht auf "on" die anderen beiden Befehle stehen nicht drin!

    ############################################################
    # Daemon
    ############################################################

    # Start in daemon (background) mode and release terminal (default: off)
    daemon on

    # File to store the process ID, also called pid file. (default: not defined)
    process_id_file /var/run/motion/motion.pid

    ############################################################
    # Basic Setup Mode
    ############################################################

    # Start in Setup-Mode, daemon disabled. (default: off)
    setup_mode off


    # Use a file to save logs messages, if not defined stderr and syslog is used. (default: not defined)
    #logfile /mnt/camshare/Cam1/motion.log
    logfile /tmp/motion.log

    # Level of log messages [1..9] (EMR, ALR, CRT, ERR, WRN, NTC, INF, DBG, ALL). (default: 6 / NTC)
    log_level 2

    # Filter to log messages by type (COR, STR, ENC, NET, DBL, EVT, TRK, VID, ALL). (default: ALL)
    log_type all

    ###########################################################
    # Capture device options
    ############################################################

    # Videodevice to be used for capturing (default /dev/video0)
    # for FreeBSD default is /dev/bktr0
    #videodevice /dev/video0

    # v4l2_palette allows to choose preferable palette to be use by motion
    # to capture from those supported by your videodevice. (default: 17)
    # E.g. if your videodevice supports both V4L2_PIX_FMT_SBGGR8 and
    # V4L2_PIX_FMT_MJPEG then motion will by default use V4L2_PIX_FMT_MJPEG.
    # Setting v4l2_palette to 2 forces motion to use V4L2_PIX_FMT_SBGGR8
    # instead.
    #
    # Values :
    # V4L2_PIX_FMT_SN9C10X : 0 'S910'
    # V4L2_PIX_FMT_SBGGR16 : 1 'BYR2'
    # V4L2_PIX_FMT_SBGGR8 : 2 'BA81'
    # V4L2_PIX_FMT_SPCA561 : 3 'S561'
    # V4L2_PIX_FMT_SGBRG8 : 4 'GBRG'
    # V4L2_PIX_FMT_SGRBG8 : 5 'GRBG'
    # V4L2_PIX_FMT_PAC207 : 6 'P207'
    # V4L2_PIX_FMT_PJPG : 7 'PJPG'
    # V4L2_PIX_FMT_MJPEG : 8 'MJPEG'
    # V4L2_PIX_FMT_JPEG : 9 'JPEG'
    # V4L2_PIX_FMT_RGB24 : 10 'RGB3'
    # V4L2_PIX_FMT_SPCA501 : 11 'S501'
    # V4L2_PIX_FMT_SPCA505 : 12 'S505'
    # V4L2_PIX_FMT_SPCA508 : 13 'S508'
    # V4L2_PIX_FMT_UYVY : 14 'UYVY'
    # V4L2_PIX_FMT_YUYV : 15 'YUYV'
    # V4L2_PIX_FMT_YUV422P : 16 '422P'
    # V4L2_PIX_FMT_YUV420 : 17 'YU12'
    #
    v4l2_palette 7

    # Tuner device to be used for capturing using tuner as source (default /dev/tuner0)
    # This is ONLY used for FreeBSD. Leave it commented out for Linux
    ; tunerdevice /dev/tuner0

    # The video input to be used (default: -1)
    # Should normally be set to 0 or 1 for video/TV cards, and -1 for USB cameras
    input -1

    # The video norm to use (only for video capture and TV tuner cards)
    # Values: 0 (PAL), 1 (NTSC), 2 (SECAM), 3 (PAL NC no colour). Default: 0 (PAL)
    norm 0

    # The frequency to set the tuner to (kHz) (only for TV tuner cards) (default: 0)
    frequency 0

    # Rotate image this number of degrees. The rotation affects all saved images as
    # well as movies. Valid values: 0 (default = no rotation), 90, 180 and 270.
    rotate 0

    # Image width (pixels). Valid range: Camera dependent, default: 352
    #width 1024
    width 1280

    # Image height (pixels). Valid range: Camera dependent, default: 288
    #height 576
    height 720

    # Maximum number of frames to be captured per second.
    # Valid range: 2-100. Default: 100 (almost no limit).
    framerate 2

    # Minimum time in seconds between capturing picture frames from the camera.
    # Default: 0 = disabled - the capture rate is given by the camera framerate.
    # This option is used when you want to capture images at a rate lower than 2 per second.
    minimum_frame_time 0

    # URL to use if you are using a network camera, size will be autodetected (incl http:// ftp:// mjpg:// or file:///)
    # Must be a URL that returns single jpeg pictures or a raw mjpeg stream. Default: Not defined
    ;netcam_url http://127.0.0.1/cgi-bin/raspicam.sh

    # Username and password for network camera (only if required). Default: not defined
    # Syntax is user:password
    ; netcam_userpass value

    # The setting for keep-alive of network socket, should improve performance on compatible net cameras.
    # off: The historical implementation using HTTP/1.0, closing the socket after each http request.
    # force: Use HTTP/1.0 requests with keep alive header to reuse the same connection.
    # on: Use HTTP/1.1 requests that support keep alive as default.
    # Default: off
    netcam_keepalive off

    # URL to use for a netcam proxy server, if required, e.g. "http://myproxy".
    # If a port number other than 80 is needed, use "http://myproxy:1234".
    # Default: not defined
    ; netcam_proxy value

    # Set less strict jpeg checks for network cameras with a poor/buggy firmware.
    # Default: off
    netcam_tolerant_check off

    # Let motion regulate the brightness of a video device (default: off).
    # The auto_brightness feature uses the brightness option as its target value.
    # If brightness is zero auto_brightness will adjust to average brightness value 128.
    # Only recommended for cameras without auto brightness
    auto_brightness off

    # Set the initial brightness of a video device.
    # If auto_brightness is enabled, this value defines the average brightness level
    # which Motion will try and adjust to.
    # Valid range 0-255, default 0 = disabled
    brightness 0

    # Set the contrast of a video device.
    # Valid range 0-255, default 0 = disabled
    contrast 0

    # Set the saturation of a video device.
    # Valid range 0-255, default 0 = disabled
    saturation 0

    # Set the hue of a video device (NTSC feature).
    # Valid range 0-255, default 0 = disabled
    hue 0

    ############################################################
    # File "camera" support - read raw YUV data from a file
    ############################################################
    #filecam_path /home/pi/test-cap/motion-mmal.capture

    ############################################################
    # OpenMax/MMAL camera support for Raspberry Pi
    ############################################################
    mmalcam_name vc.ril.camera
    #mmalcam_control_params
    #mmalcam_raw_capture_file /home/pi/motion-mmal.capture

    # Switch this setting to "on" to use the still image mode of the Pi's camera
    # instead of video. This gives a wider field of view, but requires
    # a much slower frame-rate to achieve exposure stability
    # (e.g. 0.25 fps or slower). You can use the minimum_frame_time
    # parameter above to achieve this

    mmalcam_use_still off


    ############################################################
    # Round Robin (multiple inputs on same video device name)
    ############################################################

    # Number of frames to capture in each roundrobin step (default: 1)
    roundrobin_frames 1

    # Number of frames to skip before each roundrobin step (default: 1)
    roundrobin_skip 1

    # Try to filter out noise generated by roundrobin (default: off)
    switchfilter off


    ############################################################
    # Motion Detection Settings:
    ############################################################

    # Threshold for number of changed pixels in an image that
    # triggers motion detection (default: 1500)
    threshold 1500

    # Automatically tune the threshold down if possible (default: off)
    threshold_tune off

    # Noise threshold for the motion detection (default: 32)
    noise_level 32

    # Automatically tune the noise threshold (default: on)
    noise_tune on

    # Despeckle motion image using (e)rode or (d)ilate or (l)abel (Default: not defined)
    # Recommended value is EedDl. Any combination (and number of) of E, e, d, and D is valid.
    # (l)abeling must only be used once and the 'l' must be the last letter.
    # Comment out to disable
    despeckle_filter EedDl

    # Detect motion in predefined areas (1 - 9). Areas are numbered like that: 1 2 3
    # A script (on_area_detected) is started immediately when motion is 4 5 6
    # detected in one of the given areas, but only once during an event. 7 8 9
    # One or more areas can be specified with this option. Take care: This option
    # does NOT restrict detection to these areas! (Default: not defined)
    ; area_detect value

    # PGM file to use as a sensitivity mask.
    # Full path name to. (Default: not defined)
    ; mask_file value

    # Dynamically create a mask file during operation (default: 0)
    # Adjust speed of mask changes from 0 (off) to 10 (fast)
    smart_mask_speed 0

    # Ignore sudden massive light intensity changes given as a percentage of the picture
    # area that changed intensity. Valid range: 0 - 100 , default: 0 = disabled
    lightswitch 0

    # Picture frames must contain motion at least the specified number of frames
    # in a row before they are detected as true motion. At the default of 1, all
    # motion is detected. Valid range: 1 to thousands, recommended 1-5
    minimum_motion_frames 1

    # Specifies the number of pre-captured (buffered) pictures from before motion
    # was detected that will be output at motion detection.
    # Recommended range: 0 to 5 (default: 0)
    # Do not use large values! Large values will cause Motion to skip video frames and
    # cause unsmooth movies. To smooth movies use larger values of post_capture instead.
    pre_capture 2

    # Number of frames to capture after motion is no longer detected (default: 0)
    post_capture 2

    # Event Gap is the seconds of no motion detection that triggers the end of an event.
    # An event is defined as a series of motion images taken within a short timeframe.
    # Recommended value is 60 seconds (Default). The value -1 is allowed and disables
    # events causing all Motion to be written to one single movie file and no pre_capture.
    # If set to 0, motion is running in gapless mode. Movies don't have gaps anymore. An
    # event ends right after no more motion is detected and post_capture is over.
    event_gap 60

    # Maximum length in seconds of an mpeg movie
    # When value is exceeded a new movie file is created. (Default: 0 = infinite)
    # ATTENTION: when you're not using the motion build from the tutorial, it might fail with error 'Unknown config option "max_mpeg_time"'
    # the use this line instead:
    # max_movie_time 600
    max_mpeg_time 600

    # Always save images even if there was no motion (default: off)
    emulate_motion off


    ############################################################
    # Image File Output
    ############################################################

    # Output 'normal' pictures when motion is detected (default: on)
    # Valid values: on, off, first, best, center
    # When set to 'first', only the first picture of an event is saved.
    # Picture with most motion of an event is saved when set to 'best'.
    # Picture with motion nearest center of picture is saved when set to 'center'.
    # Can be used as preview shot for the corresponding movie.
    output_pictures best

    # Output pictures with only the pixels moving object (ghost images) (default: off)
    output_debug_pictures off

    # The quality (in percent) to be used by the jpeg compression (default: 75)
    quality 75

    # Type of output images
    # Valid values: jpeg, ppm (default: jpeg)
    picture_type jpeg

    ############################################################
    # FFMPEG related options
    # Film (movies) file output, and deinterlacing of the video input
    # The options movie_filename and timelapse_filename are also used
    # by the ffmpeg feature
    ############################################################

    # Use ffmpeg to encode movies in realtime (default: off)
    ffmpeg_output_movies on

    # Use ffmpeg to make movies with only the pixels moving
    # object (ghost images) (default: off)
    ffmpeg_output_debug_movies off

    # Use ffmpeg to encode a timelapse movie
    # Default value 0 = off - else save frame every Nth second
    ffmpeg_timelapse 0

    # The file rollover mode of the timelapse video
    # Valid values: hourly, daily (default), weekly-sunday, weekly-monday, monthly, manual
    ffmpeg_timelapse_mode daily

    # Bitrate to be used by the ffmpeg encoder (default: 400000)
    # This option is ignored if ffmpeg_variable_bitrate is not 0 (disabled)
    ffmpeg_bps 500000

    # Enables and defines variable bitrate for the ffmpeg encoder.
    # ffmpeg_bps is ignored if variable bitrate is enabled.
    # Valid values: 0 (default) = fixed bitrate defined by ffmpeg_bps,
    # or the range 2 - 31 where 2 means best quality and 31 is worst.
    ffmpeg_variable_bitrate 5

    # Codec to used by ffmpeg for the video compression.
    # Timelapse mpegs are always made in mpeg1 format independent from this option.
    # Supported formats are: mpeg1 (ffmpeg-0.4.8 only), mpeg4 (default), and msmpeg4.
    # mpeg1 - gives you files with extension .mpg
    # mpeg4 or msmpeg4 - gives you files with extension .avi
    # msmpeg4 is recommended for use with Windows Media Player because
    # it requires no installation of codec on the Windows client.
    # swf - gives you a flash film with extension .swf
    # flv - gives you a flash video with extension .flv
    # ffv1 - FF video codec 1 for Lossless Encoding ( experimental )
    # mov - QuickTime ( testing )
    # ogg - Ogg/Theora ( testing )
    ffmpeg_video_codec msmpeg4

    # Use ffmpeg to deinterlace video. Necessary if you use an analog camera
    # and see horizontal combing on moving objects in video or pictures.
    # (default: off)
    ffmpeg_deinterlace off

    ############################################################
    # SDL Window
    ############################################################

    # Number of motion thread to show in SDL Window (default: 0 = disabled)
    #sdl_threadnr 0

    ############################################################
    # External pipe to video encoder
    # Replacement for FFMPEG builtin encoder for ffmpeg_output_movies only.
    # The options movie_filename and timelapse_filename are also used
    # by the ffmpeg feature
    #############################################################

    # Bool to enable or disable extpipe (default: off)
    use_extpipe off

    # External program (full path and opts) to pipe raw video to
    # Generally, use '-' for STDIN...
    ;extpipe mencoder -demuxer rawvideo -rawvideo w=320:h=240:i420 -ovc x264 -x264encopts bframes=4:frameref=1:subq=1:scenecut=-1:nob_adapt:threads=1:keyint=1000:8x8dct:vbv_bufsize=4000:crf=24:partitions=i8x8,i4x4:vbv_maxrate=800:no-chroma-me -vf denoise3d=16:12:48:4,pp=lb -of avi -o %f.avi - -fps %fps


    ############################################################
    # Snapshots (Traditional Periodic Webcam File Output)
    ############################################################

    # Make automated snapshot every N seconds (default: 0 = disabled)
    snapshot_interval 0


    ############################################################
    # Text Display
    # %Y = year, %m = month, %d = date,
    # %H = hour, %M = minute, %S = second, %T = HH:MM:SS,
    # %v = event, %q = frame number, %t = thread (camera) number,
    # %D = changed pixels, %N = noise level, \n = new line,
    # %i and %J = width and height of motion area,
    # %K and %L = X and Y coordinates of motion center
    # %C = value defined by text_event - do not use with text_event!
    # You can put quotation marks around the text to allow
    # leading spaces
    ############################################################

    # Locate and draw a box around the moving object.
    # Valid values: on, off, preview (default: off)
    # Set to 'preview' will only draw a box in preview_shot pictures.
    locate_motion_mode off

    # Set the look and style of the locate box if enabled.
    # Valid values: box, redbox, cross, redcross (default: box)
    # Set to 'box' will draw the traditional box.
    # Set to 'redbox' will draw a red box.
    # Set to 'cross' will draw a little cross to mark center.
    # Set to 'redcross' will draw a little red cross to mark center.
    locate_motion_style box

    # Draws the timestamp using same options as C function strftime(3)
    # Default: %Y-%m-%d\n%T = date in ISO format and time in 24 hour clock
    # Text is placed in lower right corner
    text_right %d.%m.%Y\n%T

    # Draw a user defined text on the images using same options as C function strftime(3)
    # Default: Not defined = no text
    # Text is placed in lower left corner
    ; text_left CAMERA %t
    text_left HofCam

    # Draw the number of changed pixed on the images (default: off)
    # Will normally be set to off except when you setup and adjust the motion settings
    # Text is placed in upper right corner
    text_changes off

    # This option defines the value of the special event conversion specifier %C
    # You can use any conversion specifier in this option except %C. Date and time
    # values are from the timestamp of the first image in the current event.
    # Default: %Y%m%d%H%M%S
    # The idea is that %C can be used filenames and text_left/right for creating
    # a unique identifier for each event.
    text_event %Y%m%d%H%M%S

    # Draw characters at twice normal size on images. (default: off)
    text_double on


    # Text to include in a JPEG EXIF comment
    # May be any text, including conversion specifiers.
    # The EXIF timestamp is included independent of this text.
    ;exif_text %i%J/%K%L

    ############################################################
    # Target Directories and filenames For Images And Films
    # For the options snapshot_, picture_, movie_ and timelapse_filename
    # you can use conversion specifiers
    # %Y = year, %m = month, %d = date,
    # %H = hour, %M = minute, %S = second,
    # %v = event, %q = frame number, %t = thread (camera) number,
    # %D = changed pixels, %N = noise level,
    # %i and %J = width and height of motion area,
    # %K and %L = X and Y coordinates of motion center
    # %C = value defined by text_event
    # Quotation marks round string are allowed.
    ############################################################

    # Target base directory for pictures and films
    # Recommended to use absolute path. (Default: current working directory)
    target_dir /mnt/camshare/Cam1

    # File path for snapshots (jpeg or ppm) relative to target_dir
    # Default: %v-%Y%m%d%H%M%S-snapshot
    # Default value is equivalent to legacy oldlayout option
    # For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-snapshot
    # File extension .jpg or .ppm is automatically added so do not include this.
    # Note: A symbolic link called lastsnap.jpg created in the target_dir will always
    # point to the latest snapshot, unless snapshot_filename is exactly 'lastsnap'
    snapshot_filename %v-%Y%m%d%H%M%S-snapshot

    # File path for motion triggered images (jpeg or ppm) relative to target_dir
    # Default: %v-%Y%m%d%H%M%S-%q
    # Default value is equivalent to legacy oldlayout option
    # For Motion 3.0 compatible mode choose: %Y/%m/%d/%H/%M/%S-%q
    # File extension .jpg or .ppm is automatically added so do not include this
    # Set to 'preview' together with best-preview feature enables special naming
    # convention for preview shots. See motion guide for details
    picture_filename %v-%Y%m%d%H%M%S-%q

    # File path for motion triggered ffmpeg films (movies) relative to target_dir
    # Default: %v-%Y%m%d%H%M%S
    # Default value is equivalent to legacy oldlayout option
    # For Motion 3.0 compatible mode choose: %Y/%m/%d/%H%M%S
    # File extension .mpg or .avi is automatically added so do not include this
    # This option was previously called ffmpeg_filename
    movie_filename %v-%Y%m%d%H%M%S

    # File path for timelapse movies relative to target_dir
    # Default: %Y%m%d-timelapse
    # Default value is near equivalent to legacy oldlayout option
    # For Motion 3.0 compatible mode choose: %Y/%m/%d-timelapse
    # File extension .mpg is automatically added so do not include this
    timelapse_filename %Y%m%d-timelapse

    ############################################################
    # Global Network Options
    ############################################################
    # Enable or disable IPV6 for http control and stream (default: off )
    ipv6_enabled off

    ############################################################
    # Live Stream Server
    ############################################################

    # The mini-http server listens to this port for requests (default: 0 = disabled)
    stream_port 8080

    # Quality of the jpeg (in percent) images produced (default: 50)
    stream_quality 50

    # Output frames at 1 fps when no motion is detected and increase to the
    # rate given by stream_maxrate when motion is detected (default: off)
    stream_motion on

    # Maximum framerate for stream streams (default: 1)
    stream_maxrate 4

    # Restrict stream connections to localhost only (default: on)
    stream_localhost off

    # Limits the number of images per connection (default: 0 = unlimited)
    # Number can be defined by multiplying actual stream rate by desired number of seconds
    # Actual stream rate is the smallest of the numbers framerate and stream_maxrate
    stream_limit 0

    # Set the authentication method (default: 0)
    # 0 = disabled
    # 1 = Basic authentication
    # 2 = MD5 digest (the safer authentication)
    stream_auth_method 0

    # Authentication for the stream. Syntax username:password
    # Default: not defined (Disabled)
    ; stream_authentication username:password


    ############################################################
    # HTTP Based Control
    ############################################################

    # TCP/IP port for the http server to listen on (default: 0 = disabled)
    webcontrol_port 8081

    # Restrict control connections to localhost only (default: on)
    webcontrol_localhost off

    # Output for http server, select off to choose raw text plain (default: on)
    webcontrol_html_output on

    # Authentication for the http based control. Syntax username:password
    # Default: not defined (Disabled)
    ; webcontrol_authentication username:password


    ############################################################
    # Tracking (Pan/Tilt)
    #############################################################

    # Type of tracker (0=none (default), 1=stepper, 2=iomojo, 3=pwc, 4=generic, 5=uvcvideo, 6=servo)
    # The generic type enables the definition of motion center and motion size to
    # be used with the conversion specifiers for options like on_motion_detected
    track_type 0

    # Enable auto tracking (default: off)
    track_auto off

    # Serial port of motor (default: none)
    ;track_port /dev/ttyS0

    # Motor number for x-axis (default: 0)
    ;track_motorx 0

    # Set motorx reverse (default: 0)
    ;track_motorx_reverse 0

    # Motor number for y-axis (default: 0)
    ;track_motory 1

    # Set motory reverse (default: 0)
    ;track_motory_reverse 0

    # Maximum value on x-axis (default: 0)
    ;track_maxx 200

    # Minimum value on x-axis (default: 0)
    ;track_minx 50

    # Maximum value on y-axis (default: 0)
    ;track_maxy 200

    # Minimum value on y-axis (default: 0)
    ;track_miny 50

    # Center value on x-axis (default: 0)
    ;track_homex 128

    # Center value on y-axis (default: 0)
    ;track_homey 128

    # ID of an iomojo camera if used (default: 0)
    track_iomojo_id 0

    # Angle in degrees the camera moves per step on the X-axis
    # with auto-track (default: 10)
    # Currently only used with pwc type cameras
    track_step_angle_x 10

    # Angle in degrees the camera moves per step on the Y-axis
    # with auto-track (default: 10)
    # Currently only used with pwc type cameras
    track_step_angle_y 10

    # Delay to wait for after tracking movement as number
    # of picture frames (default: 10)
    track_move_wait 10

    # Speed to set the motor to (stepper motor option) (default: 255)
    track_speed 255

    # Number of steps to make (stepper motor option) (default: 40)
    track_stepsize 40


    ############################################################
    # External Commands, Warnings and Logging:
    # You can use conversion specifiers for the on_xxxx commands
    # %Y = year, %m = month, %d = date,
    # %H = hour, %M = minute, %S = second,
    # %v = event, %q = frame number, %t = thread (camera) number,
    # %D = changed pixels, %N = noise level,
    # %i and %J = width and height of motion area,
    # %K and %L = X and Y coordinates of motion center
    # %C = value defined by text_event
    # %f = filename with full path
    # %n = number indicating filetype
    # Both %f and %n are only defined for on_picture_save,
    # on_movie_start and on_movie_end
    # Quotation marks round string are allowed.
    ############################################################

    # Do not sound beeps when detecting motion (default: on)
    # Note: Motion never beeps when running in daemon mode.
    quiet on

    # Command to be executed when an event starts. (default: none)
    # An event starts at first motion detected after a period of no motion defined by event_gap
    ; on_event_start value

    # Command to be executed when an event ends after a period of no motion
    # (default: none). The period of no motion is defined by option event_gap.
    ; on_event_end value

    # Command to be executed when a picture (.ppm|.jpg) is saved (default: none)
    # To give the filename as an argument to a command append it with %f
    ; on_picture_save value

    # Command to be executed when a motion frame is detected (default: none)
    ; on_motion_detected value

    # Command to be executed when motion in a predefined area is detected
    # Check option 'area_detect'. (default: none)
    ; on_area_detected value

    # Command to be executed when a movie file (.mpg|.avi) is created. (default: none)
    # To give the filename as an argument to a command append it with %f
    ; on_movie_start value

    # Command to be executed when a movie file (.mpg|.avi) is closed. (default: none)
    # To give the filename as an argument to a command append it with %f
    ; on_movie_end value

    # Command to be executed when a camera can't be opened or if it is lost
    # NOTE: There is situations when motion don't detect a lost camera!
    # It depends on the driver, some drivers dosn't detect a lost camera at all
    # Some hangs the motion thread. Some even hangs the PC! (default: none)
    ; on_camera_lost value

    #####################################################################
    # Common Options for database features.
    # Options require database options to be active also.
    #####################################################################

    # Log to the database when creating motion triggered picture file (default: on)
    ; sql_log_picture on

    # Log to the database when creating a snapshot image file (default: on)
    ; sql_log_snapshot on

    # Log to the database when creating motion triggered movie file (default: off)
    ; sql_log_movie off

    # Log to the database when creating timelapse movies file (default: off)
    ; sql_log_timelapse off

    # SQL query string that is sent to the database
    # Use same conversion specifiers has for text features
    # Additional special conversion specifiers are
    # %n = the number representing the file_type
    # %f = filename with full path
    # Default value:
    # Create tables :
    ##
    # Mysql
    # CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp(14), event_time_stamp timestamp(14));
    #
    # Postgresql
    # CREATE TABLE security (camera int, filename char(80) not null, frame int, file_type int, time_stamp timestamp without time zone, event_time_stamp timestamp without time zone);
    #
    # insert into security(camera, filename, frame, file_type, time_stamp, text_event) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')
    ; sql_query insert into security(camera, filename, frame, file_type, time_stamp, event_time_stamp) values('%t', '%f', '%q', '%n', '%Y-%m-%d %T', '%C')


    ############################################################
    # Database Options
    ############################################################

    # database type : mysql, postgresql, sqlite3 (default : not defined)
    ; database_type value

    # database to log to (default: not defined)
    ; database_dbname value

    # The host on which the database is located (default: localhost)
    ; database_host value

    # User account name for database (default: not defined)
    ; database_user value

    # User password for database (default: not defined)
    ; database_password value

    # Port on which the database is located
    # mysql 3306 , postgresql 5432 (default: not defined)
    ; database_port value

    ############################################################
    # Database Options For SQLite3
    ############################################################

    # SQLite3 database (file path) (default: not defined)
    ; sqlite3_db value


    ############################################################
    # Video Loopback Device (vloopback project)
    ############################################################

    # Output images to a video4linux loopback device
    # The value '-' means next available (default: not defined)
    ; video_pipe value

    # Output motion images to a video4linux loopback device
    # The value '-' means next available (default: not defined)
    ; motion_video_pipe value


    ##############################################################
    # Thread config files - One for each camera.
    # Except if only one camera - You only need this config file.
    # If you have more than one camera you MUST define one thread
    # config file for each camera in addition to this config file.
    ##############################################################

    # Remember: If you have more than one camera you must have one
    # thread file for each camera. E.g. 2 cameras requires 3 files:
    # This motion.conf file AND thread1.conf and thread2.conf.
    # Only put the options that are unique to each camera in the
    # thread config files.
    ; thread /usr/local/etc/thread1.conf
    ; thread /usr/local/etc/thread2.conf
    ; thread /usr/local/etc/thread3.conf
    ; thread /usr/local/etc/thread4.conf

Jetzt mitmachen!

Du hast noch kein Benutzerkonto auf unserer Seite? Registriere dich kostenlos und nimm an unserer Community teil!